Latest topics
» Carter Brothers Mini Monster truck brochure
by BlackScorpion Tue 11 Dec 2018, 7:17 pm
» How to post an image in your post /Message
by BlackScorpion Sat 02 Sep 2017, 8:23 pm
by BlackScorpion Tue 11 Dec 2018, 7:17 pm
» How to post an image in your post /Message
by BlackScorpion Sat 02 Sep 2017, 8:23 pm
Hello guest, welcome to the forum. As a guest your access is limited , In order to see the help, how to sections, you need to register. Press this box to jump to the Registration Form. A valid email is needed for registration, in order to receive a verification code to enter the forum. I look forward to you registering .
Manco Adjustable Throttle Cable Installation
Page 1 of 1 • Share
Manco Adjustable Throttle Cable Installation
Inspection
The throttle cable housing may need to be adjusted periodically because the cable stretches. When fully depressing the throttle pedal no longer activates full engine speed, adjust the throttle cable housing.
Manco Throttle Cable Installation
[You must be registered and logged in to see this image.]
* 1. Fully loosen the jam nuts (1) and (2) and mount the throttle cable housing to the frame. Make sure the throttle pedal is against the rear pedal stop (3).
* 2. Pull the throttle cable housing toward the rear of the kart until you feel resistance.
Warning: DO NOT pull the throttle cable housing any further.
* 3. Hold the cable housing in this position and screw the front jame nut (2) against the frame.
Warning: Pulling the throttle cable housing past the first point of ressistance will engage the engine throttle while the throttle pedal is in the idle position. Upon starting the engine, the vehicle may accelerate.
* 4. Screw the rear jam nut (1) against the frame.
* 5. Tighten the front jam nute (2) securely.
* 6. Make sure the engine throttle linkage is in the idle position and the throttle pedal is against the rear stop.
* 7. Block the rear end of the kart up off the ground and start the engine. If the engine is not at idle speed, stop the engine and repeat the above procedures.
Warning: The engine must be at idle speed when the throttle pedal is in the rear position. Failure to adjust the throttle properly may result in personal injury and/or vehicle damage. If you are unable to properly adjust the throttle, contact a dealer for assistance.
Make sure exposed end of the throttle cable does not interfere with throttle mechanism or cable end does not come in contact with engine ground terminal.
Inspection
The throttle cable housing may need to be adjusted periodically because the cable stretches. When fully depressing the throttle pedal no longer activates full engine speed, adjust the throttle cable housing.
Manco Throttle Cable Installation
[You must be registered and logged in to see this image.]
* 1. Fully loosen the jam nuts (1) and (2) and mount the throttle cable housing to the frame. Make sure the throttle pedal is against the rear pedal stop (3).
* 2. Pull the throttle cable housing toward the rear of the kart until you feel resistance.
Warning: DO NOT pull the throttle cable housing any further.
* 3. Hold the cable housing in this position and screw the front jame nut (2) against the frame.
Warning: Pulling the throttle cable housing past the first point of ressistance will engage the engine throttle while the throttle pedal is in the idle position. Upon starting the engine, the vehicle may accelerate.
* 4. Screw the rear jam nut (1) against the frame.
* 5. Tighten the front jam nute (2) securely.
* 6. Make sure the engine throttle linkage is in the idle position and the throttle pedal is against the rear stop.
* 7. Block the rear end of the kart up off the ground and start the engine. If the engine is not at idle speed, stop the engine and repeat the above procedures.
Warning: The engine must be at idle speed when the throttle pedal is in the rear position. Failure to adjust the throttle properly may result in personal injury and/or vehicle damage. If you are unable to properly adjust the throttle, contact a dealer for assistance.
Make sure exposed end of the throttle cable does not interfere with throttle mechanism or cable end does not come in contact with engine ground terminal.
Similar topics
Create an account or log in to leave a reply
You need to be a member in order to leave a reply.
Page 1 of 1
Permissions in this forum:
You cannot reply to topics in this forum